Measurement of Airborne Particles and Volatile Organic Compounds Produced During the Heat Treatment Process in Manufacturing Welding Materials

Background@#There is little information about the airborne hazardous agents released during the heat treatment when manufacturing a welding material. This study aimed to evaluate the airborne hazardous agents generated at welding material manufacturing sites through area sampling. @*Methods@#concentration of airborne particles was measured using a scanning mobility particle sizer and optical particle sizer. Total suspended particles (TSP) and respirable dust samples were collected on polyvinyl chloride filters and weighed to measure the mass concentrations. Volatile organic compounds and heavy metals were analyzed using a gas chromatography mass spectrometer and inductively coupled plasma mass spectrometer, respectively. @*Results@#The average mass concentration of TSP was 683.1 ± 677.4 μg/m3, with respirable dust accounting for 38.6% of the TSP. The average concentration of the airborne particles less than 10 μm in diameter was 11.2–22.8 × 104 particles/cm3, and the average number of the particles with a diameter of 10–100 nm was approximately 78–86% of the total measured particles (<10 μm). In the case of volatile organic compounds, the heat treatment process concentration was significantly higher (p < 0.05) during combustion than during cooling. The airborne heavy metal concentrations differed depending on the materials used for heat treatment. The content of heavy metals in the airborne particles was approximately 32.6%. @*Conclusions@#Nanoparticle exposure increased as the number of particles in the air around the heat treatment process increases, and the ratio of heavy metals in dust generated after the heat treatment process is high, which may adversely affect workers' health.

Occupational Exposure during Intraperitoneal Pressurized Aerosol Chemotherapy Using Doxorubicin in a Pig Model

Background@#This study evaluated occupational exposure levels of doxorubicin in healthcare workers performing rotational intraperitoneal pressurized aerosol chemotherapy (PIPAC) procedures. @*Methods@#All samples were collected during PIPAC procedures applying doxorubicin to an experimental animal model (pigs). All procedures were applied to seven pigs, each for approximately 44 min. Surface samples (n = 51) were obtained from substances contaminating the PIPAC devices, surrounding objects, and protective equipment. Airborne samples were also collected around the operating table (n = 39). All samples were analyzed using ultra-high performance liquid chromatography-mass spectrometry. @*Results@#Among the surface samples, doxorubicin was detected in only five samples (9.8%) that were directly exposed to antineoplastic drug aerosols in the abdominal cavity originating from PIPAC devices. The telescopes showed concentrations of 0.48–5.44 ng/cm2 and the trocar showed 0.98 ng/cm2 in the region where the spraying nozzles were inserted. The syringe line connector showed a maximum concentration of 181.07 ng/cm2, following a leakage. Contamination was not detected on the surgeons' gloves or shoes. Objects surrounding the operating table, including tables, operating lights, entrance doors, and trocar holders, were found to be uncontaminated. All air samples collected at locations where healthcare workers performed procedures were found to be uncontaminated. @*Conclusions@#Most air and surface samples were uncontaminated or showed very low doxorubicin concentrations during PIPAC procedures. However, there remains a potential for leakage, in which case dermal exposure may occur. Safety protocols related to leakage accidents, selection of appropriate protective equipment, and the use of disposable devices are necessary to prevent occupational exposure.

Overview of Legal Measures for Managing Workplace COVID-19 Infection Risk in Several Asia-Pacific Countries

Background@#Despite the lack of official COVID-19 statistics, various workplaces and occupations have been at the center of COVID-19 outbreaks. We aimed to compare legal measures and governance established for managing COVID-19 infection risks at workplaces in nine Asia and Pacific countries and to recommend key administrative measures. @*Methods@#We collected information on legal measures and governance from both general citizens and workers regarding infection risks such as COVID-19 from industrial hygiene professionals in nine countries (Indonesia, India, Japan, Malaysia, New Zealand, Republic of the Philippines, Republic of Korea, Taiwan, and Thailand) using a structured questionnaire. @*Results@#A governmental body overseeing public health and welfare was in charge of containing the spread and occurrence of infectious diseases under an infectious disease control and prevention act or another special act, although the name of the pertinent organizations and legislation vary among countries. Unlike in the case of other traditional hazards, there have been no specific articles or clauses describing the means of mitigating virus risk in the workplace that are legally required of employers, making it difficult to define the responsibilities of the employer. Each country maintains own legal systems regarding access to the duration, administration, and financing of paid sick leave. Many workers may not have access to paid sick leave even if it is legally guaranteed. @*Conclusion@#Specific legal measures to manage infectious disease risks, such as providing proper personal protective equipment, education, engineering control measures, and paid sick leave are recommended to be stipulated in Industrial safety and health-related acts.

Evaluation of Short-Term Exposure Levels on Ammonia and Hydrogen Sulfide During Manure-Handling Processes at Livestock Farms

Background@#Ammonia and hydrogen sulfide are harmful gases generated during aerobic/anaerobic bacterial decomposition of livestock manure. We evaluated ammonia and hydrogen sulfide concentrations generated from workplaces at livestock farms and determined environmental factors influencing the gas concentrations. @*Methods@#Five commercial swine farms and five poultry farms were selected for monitoring. Real-time monitors were used to measure the ammonia and hydrogen sulfide concentrations and environmental conditions during the manure-handling processes. Monitoring was conducted in the manure storage facility and composting facility. Information on the farm conditions was also collected through interview and walk-through survey. @*Results@#The ammonia concentrations were significantly higher at the swine composting facilities (9.5–43.2 ppm) than at other manure-handling facilities at the swine and poultry farms, and high concentrations of hydrogen sulfide were identified during the manure agitation and mixing process at the swine manure storage facilities (6.9–19.5 ppm). At the poultry manure-handling facilities, the ammonia concentration was higher during the manure-handling processes (2.6–57.9 ppm), and very low hydrogen sulfide concentrations (0–3.4 ppm) were detected. The air temperature and relative humidity, volume of the facility, duration of manure storage, and the number of animals influenced the gas concentrations. @*Conclusion@#A high level of hazardous gases was generated during manure handling, and some levels increased up to risk levels that can threaten workers' health and safety. Some of the farm operational factors were also found to influence the gas levels. By controlling and improving these factors, it would be possible to protect workers' safety and health from occupational risks.

Chemical Use and Associated Health Concerns in the Semiconductor Manufacturing Industry

Background@#Research on the status of many chemicals used in the semiconductor industry is needed. The purpose of this study was to describe the overall status of chemical use in the semiconductor industry in Korea and to examine it from a health perspective. @*Methods@#Data on the status of chemical use and safety data sheets at 11 of 12 major semiconductor workplaces in Korea were collected. The number of chemical products and chemical constituents, quantities of chemicals, and trade secret ingredients used, as well as the health hazards were examined. @*Results@#On average, 210 chemical products and 135 chemical constituents were used at the surveyed workplaces. Among all chemical products, 33% (range: 16–56%) contained at least one trade secret ingredient. Most of the trade secret ingredients were used in the photolithography process. Several carcinogens, including sulfuric acid, chromic acid, ethylene oxide, crystalline silica, potassium dichromate, and formaldehyde were also used. Only 29% (39 of 135) of the chemical constituents had occupational exposure limits, and more than 60% had no National Fire Protection Association health, safety, and reactivity ratings. Based on the aforementioned results, this study revealed the following. First, many chemical products and constituents are being used in the semiconductor industry and many products contained trade secret ingredients. Second, many products contained significant amounts of carcinogenic, mutagenic, and reproductive toxicant materials. @*Conclusion@#We conclude that protecting workers in the semiconductor industry against harm from chemical substances will be difficult, due to widespread use of trade secret ingredients and a lack of hazard information. The findings of the status of chemical use and the health and safety risks in semiconductor industry will contribute to epidemiological studies, safe workplace, and worker health protection.

Chemical Use and Associated Health Concerns in the Semiconductor Manufacturing Industry

Background@#Research on the status of many chemicals used in the semiconductor industry is needed. The purpose of this study was to describe the overall status of chemical use in the semiconductor industry in Korea and to examine it from a health perspective. @*Methods@#Data on the status of chemical use and safety data sheets at 11 of 12 major semiconductor workplaces in Korea were collected. The number of chemical products and chemical constituents, quantities of chemicals, and trade secret ingredients used, as well as the health hazards were examined. @*Results@#On average, 210 chemical products and 135 chemical constituents were used at the surveyed workplaces. Among all chemical products, 33% (range: 16–56%) contained at least one trade secret ingredient. Most of the trade secret ingredients were used in the photolithography process. Several carcinogens, including sulfuric acid, chromic acid, ethylene oxide, crystalline silica, potassium dichromate, and formaldehyde were also used. Only 29% (39 of 135) of the chemical constituents had occupational exposure limits, and more than 60% had no National Fire Protection Association health, safety, and reactivity ratings. Based on the aforementioned results, this study revealed the following. First, many chemical products and constituents are being used in the semiconductor industry and many products contained trade secret ingredients. Second, many products contained significant amounts of carcinogenic, mutagenic, and reproductive toxicant materials. @*Conclusion@#We conclude that protecting workers in the semiconductor industry against harm from chemical substances will be difficult, due to widespread use of trade secret ingredients and a lack of hazard information. The findings of the status of chemical use and the health and safety risks in semiconductor industry will contribute to epidemiological studies, safe workplace, and worker health protection.

Evaluation of Hazardous Chemicals with Material Safety Data Sheet and By-products of a Photoresist Used in the Semiconductor-Manufacturing Industry

BACKGROUND: The photolithography process in the semiconductor industry uses various chemicals with little information on their constitution. This study aimed to identify the chemical constituents of photoresist (PR) products and their by-products and to compare these constituents with material safety data sheets (MSDSs) and analytical results. METHODS: A total of 51 PRs with 48 MSDSs were collected. Analysis consisted of two parts: First, the constituents of the chemical products were identified and analyzed using MSDS data; second, for verification of the by-products of PR, volatile organic compounds were analyzed. The chemical constituents were categorized according to hazards. RESULTS: Forty-five of 48 products contained trade secrets in amounts ranging from 1 to 65%. A total of 238 ingredients with multiple counting (35 ingredients without multiple counting) were identified in the MSDS data, and 48.7% of ingredients were labeled as trade secrets under the Korea Occupational Safety and Health Act. The concordance rate between the MSDS data and the analytical result was 41.7%. The by-product analysis identified 129 chemicals classified according to Chemical Abstracts Service No., with 17 chemicals that are carcinogenic, mutagenic, and reprotoxic substances. Formaldehyde was found to be released from 12 of 21 products that use novolak resin. CONCLUSION: We confirmed that several PRs contain carcinogens, and some were not specified in the toxicological information in the MSDS. Hazardous chemicals, including benzene and formaldehyde, are released from PRs products as by-products. Therefore, it is necessary to establish a systematic management system for chemical compounds and the working environment.

IgA nephropathy in a laboratory worker that progressed to end-stage renal disease: a case report

BACKGROUND: IgA nephropathy (IgAN) is the most common form of glomerulonephritis, a principal cause of end-stage renal disease (ESRD) worldwide. The mechanisms of onset and progression of IgAN have not been fully revealed, and epidemiologic studies have yielded diverging opinions as to the role of occupational exposure to organic solvents in the initiation or worsening of IgAN. As the authors encountered a laboratory worker with IgAN that progressed to ESRD, we present a case report of IgAN progression due to dichloromethane exposure along with a review of literature. CASE PRESENTATION: A 41-year-old male laboratory worker began to experience gross painless hematuria after two years of occupational exposure to toluene. Although clinical follow-up was initiated under the impression of IgAN based on clinical findings, the patient continued to work for four more years in the same laboratory, during which he was in charge of laboratory analysis with direct exposure to a high concentration of dichloromethane without proper protective equipment. During that time, his renal function rapidly worsened and finally progressed to ESRD 10 years after the first clinical symptoms. The result of exposure assessment through reenactment of his work exceeded the occupational exposure limit for dichloromethane to a considerable degree. CONCLUSIONS: The causal association between occupational solvent exposure and IgAN is still unclear; therefore, this case report could be used as a basis to support the relevance of occupational solvent exposure to IgAN and/or its progression. Early intervention as well as close monitoring of laboratory workers exposed to various organic solvents is important to prevent or delay the progression of glomerulonephritis to ESRD in the occupational setting.

Comparison of Real Time Nanoparticle Monitoring Instruments in the Workplaces

BACKGROUND: Relationships among portable scanning mobility particle sizer (P-SMPS), condensation particle counter (CPC), and surface area monitor (SAM), which are different metric measurement devices, were investigated, and two widely used research grade (RG)-SMPSs were compared to harmonize the measurement protocols. METHODS: Pearson correlation analysis was performed to compare the relation between P-SMPS, CPC, and SAM and two common RG-SMPS. RESULTS: For laboratory and engineered nanoparticle (ENP) workplaces, correlation among devices showed good relationships. Correlation among devices was fair in unintended nanoparticle (UNP)-emitting workplaces. This is partly explained by the fact that shape of particles was not spherical, although calibration of sampling instruments was performed using spherical particles and the concentration was very high at the UNP workplaces to allow them to aggregate more easily. Chain-like particles were found by scanning electron microscope in UNP workplaces. The CPC or SAM could be used as an alternative instrument instead of SMPS at the ENP-handling workplaces. At the UNP workplaces, where concentration is high, real-time instruments should be used with caution. There are significant differences between the two SMPSs tested. TSI SMPS showed about 20% higher concentration than the Grimm SMPS in all workplaces. CONCLUSIONS: For nanoparticle measurement, CPC and SAM might be useful to find source of emission at laboratory and ENP workplaces instead of P-SMPS in the first stage. An SMPS is required to measure with high accuracy. Caution is necessary when comparing data from different nanoparticle measurement devices and RG-SMPSs.

Estimating Benzene Exposure Level over Time and by Industry Type through a Review of Literature on Korea

The major purpose of this study is to construct a retrospective exposure assessment for benzene through a review of literature on Korea. Airborne benzene measurements reported in 34 articles were reviewed. A total of 15,729 individual measurements were compiled. Weighted arithmetic means [AM(w)] and their variance calculated across studies were summarized according to 5-year period intervals (prior to the 1970s through the 2010s) and industry type. Industries were classified according to Korea Standard Industrial Classification (KSIC) using information provided in the literature. We estimated quantitative retrospective exposure to benzene for each cell in the matrix through a combination of time and KSIC. Analysis of the AM(w) indicated reductions in exposure levels over time, regardless of industry, with mean levels prior to the 1980e1984 period of 50.4 ppm (n = 2,289), which dropped to 2.8 ppm (n = 305) in the 1990e1994 period, and to 0.1 ppm (n = 294) in the 1995e1999 period. There has been no improvement since the 2000s, when the AM(w) of 4.3 ppm (n = 6,211) for the 2005e2009 period and 4.5 ppm (n = 3,358) for the 2010e2013 period were estimated. A comparison by industry found no consistent patterns in the measurement results. Our estimated benzene measurements can be used to determine not only the possibility of retrospective exposure to benzene, but also to estimate the level of quantitative or semiquantitative retrospective exposure to benzene.

Much Concern but Little Research on Semiconductor Occupational Health Issues

No abstract available.